Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor Bedienungsanleitung PDF herunterladen

Sensor Frequency = ___________________________ Hz

Technical note:

Sensor frequency MUST be greater than 45 Hz for full scale

needle deﬂ ection.

3. Calculate the actual max. ﬂ ow rate in your process line as follows:

Maximum ﬂ ow rate = Sensor frequency (step 2) × A-Factor (Section 6)

Maximum Flow Rate = __________________________________

2. Calibration

The 5090/515 ﬂ ow metering system utilizes the AC signal

amplitude from the 515 sensor to drive the 5090 meter.

The front panel meter movement adjustment (SPAN) is easily

accessed under the removable front window for simple calibration.

A dial kit with six dial ranges, assorted ﬂ ow unit/multiplier decals,

and dial installation instructions is included for your convenience.

1. Compatible Sensor Wiring

Frequency

counter

Red

Black

GPM

X100

SPAN

Signet Monitor

4. Install the appropriate dial face and ﬂ ow unit/multiplier decal

for the maximum ﬂ ow rate (Step 3). Refer to dial installation

instructions included with dial kit.

The dial kit includes the following:

Example: A ﬂ ow system's maximum ﬂ ow rate is 18.3 GPM.

The proper dial and ﬂ ow unit/multiplier decal for this ﬂ ow system is:

0 - 2 dial + GPM × 10 decal.

5. Disconnect frequency counter.

Access and adjust the "SPAN" potentiometer to match the

calculated maximum ﬂ ow rate from Step 3.

After adjustment, calibration is complete.

5090

Rotor

w/magnets

Black

Red

515 Circuit

Shield

SPAN

X 100

GPM

SPAN

Signet Monitor

6 Dials:

0-2

0-4

0-6

0-8

0-10

0-100

Assorted Unit and Multiplier Decals:

X 10

X 100

X 1,000

X 10,000

LPM

x 1,000

GPM

x 10

SPAN

Signet 5090 Flow Monitor

Technical Notes:

• Remove terminal block for easy wiring (Fig. 1)

• Maintain cable shield through cable splice.

• Route sensor cable away from AC power lines.

• Use 2-conductor shielded cable for sensor cable extension up

to 61 m (200 ft).

English

Red

Blk

Shld

Sensor

Input

515

Black (AC signal out)

Red (AC signal out)

Silver (shield)

5090 Rear

Terminal

Connection

Red

Blk

Shld

Sensor

Input

Red

Blk

Shld

Sensor

Input

LISTED

77CJ

Fig. 1

*3-5090.090-1*

3-5090.090-1 Rev. K 08/13

Procedure

1. Induce the maximum (stable) ﬂ ow rate in your process line.

2. Using the frequency counter, monitor and record the 515

sensor frequency output:

Equipment Required

• Frequency counter

• Signet 515 Sensor installed in process line

• Standard and phillips head screwdriver

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Signet 5090 Flow Monitor

Sensor Frequency = ___________________________ HzTechnical note: Sensor frequency MUST be greater than 45 Hz for full scale needle deﬂ ection.3. Calcu

Seite 2 - 5. Maintenance

2Signet 5075 Flow MonitorSIDE VIEW Mounting Clamp (2 ea.) Optional Splashproof Rear Cover 88 mm (3.5 in.) Mounting Panel Panel Gasket 91 mm (3.6 in.)

Seite 3

3Signet 5090 Flow Monitor 6. Signet 515 Flow Sensor A-Factors-------------- A-FACTORS ----------------PIPESIZESIGNETFITTING------------------- 1 Hz =

Seite 4 - A-Factors for DIN Pipes

------------------------------ A-FACTORS -------------------------------PIPESIZESIGNETFITTING---------------------------------- 1 Hz = ---------------

Weitere Dokumente für Werkzeug Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor

Um das Dokument anzuzeigen Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor Bedienungsanleitung

Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor Bedienungsanleitung (4 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Werkzeug Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor herunter. GF Signet 5090 Sensor-Powered ProPoint Flow Monitor User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Werkzeug Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Werkzeug Gf-signet 5090 Sensor-Powered ProPoint Flow Monitor